Gerber PermaGrip Film White

Description

Gerber PermaGrip Film White

FilmPermaGrip 15” Punched EDGE READY Color 10 Yard 50 Yard White AP75517 AP75517

residue on sprocketed equipment. Gerber PermaGrip is ideally suited for a wide variety of commercial, industrial and safety applications. It can be used to create interior and exterior labels, emblems, logos and signs on many surfaces including, flat, moderately compound curved and moderately-rough surfaces and some low surface energy materials. The user should determine the suitability of all substrates prior to actual application. This film is not recommended for use on corrugated, riveted or highly irregular surfaces. It is not recommended for flexible sign face or flexible banner material. It is also not intended for applications where petrochemical contact may occur. If petrochemical exposure is anticipated, refer to the Product Bulletin for information on protecting graphics.

Gerber PermaGrip is a durable, permanent cast vinyl film for use with Gerber EDGE Systems and GerberColor foils. It is dimensionally stable and has an extremely aggressive pigmented adhesive system that provides superior hiding power when applied over colored surfaces. Gerber PermaGrip is edge-stripped to eliminate buildup of adhesive

DESCRIPTION
Gerber PermaGrip is a durable, permanent cast vinyl film that has been custom formulated by
3M for use with the GERBER EDGE®, GERBER EDGE 2®, and GERBER EDGE FX thermal
transfer printing systems, in conjunction with GerberColor™ Foils. It is dimensionally stable and
has an extremely aggressive pigmented adhesive system that provides superior hiding power
when applied over colored surfaces. Gerber PermaGrip is edge-stripped to eliminate build up of
adhesive residue on sprocketed equipment.
PRODUCT CHARACTERISTICS
Property Description
Film Color White
Adhesive Type Grey, pressure sensitive
Liner 78-lb white kraft paper
Application Surfaces Flat or moderate compound curves, with and without rivets
Minimum Application
Temperature
40F (4C)
Page 2 of 5
INTENDED APPLICATIONS
Gerber PermaGrip is ideally suited for a wide variety of commercial, industrial and safety
applications. It can be used to create interior and exterior labels, emblems, logos and signs on
many surfaces including, flat, moderately compound curved and moderately-rough surfaces and
some low surface energy materials. The user should determine the suitability of all substrates
prior to actual application.
This film is not recommended for use on corrugated, riveted or highly irregular surfaces. It is not
recommended for flexible signface or flexible banner material. It is also not intended for
applications where petrochemical contact may occur. If petrochemical exposure is anticipated,
refer to the section below on protecting graphics.
PERFORMANCE LIFE (UNPRINTED)
Gerber PermaGrip has the following expected performance life:
Exposure Type
Unprinted Film Performance Life
(years)
US Desert
Southwest
Vertical Exposure
Face of graphic is less than 10 from vertical
7 4
Non-Vertical Exposure
Face of graphic is more than 10 from vertical
4 2
Performance statements are based upon field experience and exposure tests conducted
throughout the United States. Substrate selection, exposure angle, environmental conditions,
and maintenance of markings will affect actual performance. Continuous exposure in regions
that experience maximum sunny days will result in decreased performance. Unprinted, this
product has an expected durability of four years.
SHELF LIFE AND STORAGE
Apply film within one year of receipt. Printed graphics should also be applied within one year.
Film and printed graphics (with or without premask) should be kept in a clean area free from
excessive moisture and direct sunlight. Maintain temperature at less than 100°F (38°C). Use a
paper interleaf between layers of stacked or rolled printed materials. Do not stack printed
graphics face to face.
PRINTING
GerberColor Spot (GCS), GerberColor Process Pro CMYK (GCP), GerberColor Medal (GCM),
GerberColor Transparent (GCT) Series, ColorSet™ Spot (CSS), and ColorSet Process (CSP)
Series Foils can be used to print onto PermaGrip.
Recommended working environment is as follows:
 Operating temperature: 50ºF to 95ºF / 10ºC to 35ºC
 Recommended temperature for assured printing accuracy: 68ºF to 78ºF / 20ºC to 26ºC
 Operating humidity: 20% to 90% relative humidity, non-condensing (maximum range;
actual range varies by material used)
Page 3 of 5
PROTECTING GRAPHICS
Gerber Technology offers products that are designed to protect vinyl and printed graphics.
Gerber Guard manufactured by 3M is a durable, dimensionally stable, glossy vinyl
overlaminate. This film has a petrochemical-resistant construction and is intended to be used
when markings may be exposed to petrochemical spillage and/or severe handling conditions.
Gerber UVGuard is a custom-formulated, 1-mil, clear, extremely durable polyvinyl fluoride
(PVF) laminating film designed to further expand the resistance to weathering of printed
graphics for up to five years.
Gerber UVGuard™ 9 manufactured by 3M is a 2-mil, glossy, clear, mildew-resistant, polyvinyl
fluoride laminating film with a petrochemical-resistant adhesive system. It is designed to further
expand the resistance to weathering of printed graphics up to nine years. Gerber UVGuard 9
has the highest protection from UV fade.
Gerber StrikeGuard™ is an 8.0-mil, clear, glossy overlaminate film designed for a variety of
applications. This heavy-duty overlaminate film is ideal for the protection of graphics, up to two
years, and is especially beneficial where printed graphics experience severe handling and
forceful impact. Gerber StrikeGuard is not recommended in applications that require
petrochemical protection or where additional UV or vandal resistance is desired.
Abrasion Guard SPF (Sign Protection Formula) is a clear, top-coat GerberColor Finishing
Series (GCF) Foil designed for use with EDGE® Series thermal transfer printing systems, to
protect graphics from moderate contact and exposure to harmful effects of UV rays. It has an
expected performance life of up to five years (when printed by itself). When applied as a
protective overprint on other GerberColor Foils, Abrasion Guard SPF will extend the life of the
base color by up to 30%.
CUTTING
Gerber PermaGrip can be cut on any 15-inch EDGE-compatible sprocketed plotter. Plotters can
be set to full speed. The user should perform a test cut to determine the ideal tool force setting.
SUBSTRATE PREPARATION
Before applying your graphic, wash the surface of your substrate with warm water and
detergent. Do not use soaps or other cleaners with lotions or creams as they will leave a
residue. Thoroughly rinse the surface and allow it to completely dry. Saturate a clean paper
towel with a solvent-based cleaner and wipe the substrate surface. Be certain to follow all
manufacturer safety guidelines when using any solvent. Dry the surface with a lint-free paper
towel before the solvent evaporates. If applying to glass, solvent wipe the surface with a 2 to 1
mixture of water and isopropyl alcohol. Glass temperatures can vary across the surface. These
temperature variations can produce stresses which may cause the glass to break. Use caution
when applying to glass. Some polycarbonate substrates may weaken when certain vinyl films
are applied to them. Because of this possibility, the user will need to determine if safety items
such as helmets, safety shields, and some windshields are compatible with their vinyl’s
adhesive.
Many paint systems (e.g. two-part urethane) and some polycarbonate substrates will outgas if
they are not fully cured. Outgassing can cause permanent bubbling in most films; substrates
should be tested for outgassing prior to final application.
Page 4 of 5
APPLICATION TECHNIQUES
Both wet and dry application methods can be used with Gerber PermaGrip and panels should
be overlapped.
Care should be used during graphic application because the aggressive adhesive system is not
positionable and becomes more aggressive as the surface temperature of the final substrate
increases.
Gerber standard tack application tape is required for all EDGE-printed graphics.
MAINTENANCE
To clean printed graphics, use a mild, non-abrasive soap with a soft cloth or sponge. Avoid
using alcohol-based cleansers or soaps containing grit or abrasives. Automated vehicle washing
systems that use rotary cleaning brushes should also be avoided.
PHYSICAL CHARACTERISTICS
Property English Units Metric Units
Thickness (Film + Adhesive) 0.003 to 0.004 in .08 to .10 mm
Tensile Strength 5 lb/in at 73ºF 0.9 kg/cm at 23ºC
Applied Shrinkage .047 in 1.2 mm
Service Temperature Range -65ºF to 225ºF -54ºC to 107ºC
ADHESION (24 hours after application)
Substrate English Units (lb-in) Metric Units (kg-cm)
ABS 5 0.9
Acrylic Enamel 5 0.9
Anodized Aluminum 6 1.1
Etched Aluminum 5 0.9
Chrome 5 0.9
Fiberglass 5 0.9
CHEMICAL RESISTANCE (UNPRINTED)
 Resists mild acids, alkalis, and salts.
 Excellent water resistance.
RELATED LITERATURE
Refer to Product Bulletins of relevant foils and materials for product-specific handling,
production, and finishing information.
Page 5 of 5
CONTACT INFORMATION
For help with questions concerning Gerber products, please call your distributor or Gerber
Customer Service at 1-800-222-7446 or (860) 644-1551. Visit us on the Internet at
www.gerbertechnology.com/signage to learn more about our many other foils, materials and
equipment.
When sold by Gerber, use only the corresponding Gerber Product Bulletin to determine product details, including but not limited to appropriate uses, warranty and processing.
EDGE, GERBER EDGE, GERBER EDGE 2, Gerber Scientific Products, GerberCal, GerberGraphics, GRAPHIX ADVANTAGE, GSP, and Images on Vinyl are Registered
Trademarks of Gerber Technology.
Abrasion Guard, ColorSet, EDGE Positive, EDGE READY, Gerber AutoMag, GERBER EDGE FX, Gerber FastFacts, Gerber Guard, Gerber HoloGraphix, Gerber ImageCal,
Gerber ImageCast, Gerber InstaChange, Gerber OMEGA, Gerber PermaGrip, Gerber PlastiGraphix, Gerber QUANTUM, Gerber StrikeGuard, Gerber Tone, Gerber UVGuard,
GerberCal, GerberColor, GerberColor Spectratone, GerberGauge, GerberGlow, GerberMag, GerberMask, GerberVision, GS 15, GS15plus, GSP Plot, GSxplus, GSx,
ImagePerfect, IMAGE READY, LexEdge, Matched Technology System, MTS, OMEGA, Process Pro, SpectraShade, and SpectraTint are Trademarks of Gerber Technology.
PANTONE, and other Pantone, Inc., trademarks are the property of Pantone, Inc.
LEXAN is a Registered Trademark of General Electric Company.
3M is a trademark of 3M Company.
enVision is a trademark of 3M Company that is licensed to Gerber.
©2018 Gerber Technology. All Right Reserved
Category: EDGE READY™ FastFact #: 5545 Supplied by: Aftermarkets Last Modified: 02/27/18