Description
Avery MPI1005SC EASY APPLY RS 2.1 mil White Gloss Cast Vinyl
Easy Apply RS adhesive system with air egress channels to easily eliminate bubble and wrinkle during application Slides smoothly on surface for exact positioning: RS technology stands-off from surface until pressure is applied Low adhesive tack level allows graphics to be repositioned during application Excellent printability on eco-solvent, solvent, latex and UV curable printers StaFlat liner provides easy handling and converting properties Supercast technology ensures superior conformability to irregular surfaces Outstanding outdoor durability and performance Excellent dimensional stability High gloss finish for superior automotive paint-like appearance Grey adhesive provides extra opacity for blockout performance Easy removability with heat for up to 5 years with little or no adhesive residue
Avery Dennison® MPI 1005 SC Easy Apply RS*
Gloss White Supercast with Easy Apply RS Technology
Description
Film: 53 micron high gloss
white Supercast vinyl
Adhesive: Grey permanent
acrylic with Easy Apply RS
and long term removability
Removability: Up to 5 years
Backing: Two side PE
coated StaFlat paper,
145g/m2
Outdoor life**: Up to 10
years unprinted
Application surface: Flat,
simple curves, rivets and
compound curves
Features
Easy Apply RS adhesive system with air egress channels to easily eliminate
bubble and wrinkle during application
Slides smoothly on surface for exact positioning: RS technology stands-off
from surface until pressure is applied
Low adhesive tack level allows graphics to be repositioned during application
Excellent printability on eco-solvent, solvent, latex and UV curable printers
StaFlat liner provides easy handling and converting properties
Supercast technology ensures superior conformability to irregular surfaces
Outstanding outdoor durability and performance
Excellent dimensional stability
High gloss finish for superior automotive paint-like appearance
Grey adhesive provides extra opacity for blockout performance
Easy removability with heat for up to 5 years with little or no adhesive residue
Conversion +
Flat bed cutters Cold overlaminating
Friction fed cutters Electrostatic printing
Die cutting Latex inkjet
Thermal transfer Eco solvent inkjet
Screen printing Solvent inkjet
Offset printing UV curable inkjet
+
Always test with your combination of printer and inks prior to commercial use.
Common Applications
Flat sided trucks
Corrugated trucks
Cars and vans
Trains and light rail
Buses
Marine vessels
Corporate Signage
Application
Avery Dennison recommend a maximum total ink limit of 270% to ensure optimal performance
Product is recommended for application in to deep recessed areas of vehicles, when combined with DOL 1460 or DOL 1480.
Dry application only. Do not use water and detergent or a commercial application fluid to position the graphic.
Refer to Instructional Bulletins 1.14, 1.15, 1.17 & 4.14 for printing and application instructions
Uses
Avery Dennison MPI 1005 Supercast Easy Apply RS is a premium gloss white
opaque cast vinyl film designed for ease of application on long term outdoor
signage or fleet applications where superior conformability, durability, high opacity,
outdoor performance and clean and easy removal are required.
Avery Dennison Graphics Solutions Asia Pacific
www.graphicsap.averydennison.com
General
Calliper, face film ISO 534 53 micron
Calliper, face film & adhesive ISO 534 80 micron
Gloss ISO 2813, 20° 50%
Dimensional stability DIN 30646 0.4 mm max
Elongation DIN 53455 (Unprinted film) > 100%
Adhesion, 15 mins FINAT FTM-1, Stainless steel 315 N/m
Adhesion, 24 hrs FINAT FTM-1, Stainless steel 367 N/m
Adhesion, 1 week FINAT FTM-1, Stainless steel 700 N/m
Removability ^^ Smooth OEM painted surfaces Up to 10 years
Flammability Self extinguishing
Shelf life Stored at 22° C/50-55 % RH 2 years
Durability ** Vertical exposure ^ Up to 10 years (unprinted)
^ See ICS Performance Guarantee Durability Bulletin for your
specific printer and ink combination for further information
^^ Not removable when applied to nitrocellulose paints, fresh
screenprint inks, ABS, polystyrene & certain types of PVC
Note:
Materials have to be properly dried and cured before further processing, like
laminating, varnishing, trimming, contour cutting or application. The residual
solvents can otherwise change the products specific features and properties.
Chemical
Humidity resistance 120 hours exposure No effect
Corrosion resistance 120 hours exposure No contribution to corrosion
Water resistance 48 hour immersion No effect
Chemical resistance Mild acids No effect
Mild alkalis No effect
Solvent resistance Applied to aluminium No effect exposed to:
Oils, greases, aliphatic
solvents, motor oils,
heptanes, kerosene, JP-4 fuel
Thermal
Application temperature Minimum: + 10o
C
Temperature range – 45o
C to + 82o
C
Important
Information on physical characteristics is based
upon tests we believe to be reliable. The values
listed herein are typical values and are not for use
in specifications.
They are intended only as a source of information
and are given without guarantee and do not
constitute a warranty. Purchasers should
independently determine, prior to use, the
suitability of any material for their specific use.
All technical data is subject to change without
prior notice.
Warranty
Avery Dennison® materials are manufactured
under careful quality control and are warranted to
be free from defect in material and workmanship.
Any material shown to our satisfaction to be
defective at the time of sale will be replaced
without charge. Our aggregate liability to the
purchaser shall in no circumstances exceed the
cost of the defective materials supplied. No
salesman, representative or agent is authorised
to give guarantee, warranty, or make any
representation contrary to the foregoing.
All Avery Dennison® materials are sold subject to
the above conditions, being part of our
standard conditions of sale, a copy of which is
available on request.
**Expected Durability
The expected durability of Avery Dennison films
are defined as the expected performance life of
the Avery Dennison graphic film(s) within Zone 1
of the Avery Dennison zone system, in outdoor
vertical exposure conditions.
The actual performance life will depend on a
variety of factors, including selection and
preparation of substrate, angle and direction of
exposure, application methods, environmental
conditions and cleaning/maintenance of the films.
In case of films used in areas of high
temperatures or humidity, high altitudes and
industrially polluted areas the performance will be
further reduced.
Expected Durability and Warranted Period
Definitions
Expected durability is the expected period of
time defined in the product data sheet, the
product should, but is not warranted to, perform
satisfactorily when applied in vertical exposure
conditions as defined in Instructional Bulletin
1.30. The warranted period as defined in the
appropriate ICS Performance Guarantee Bulletin,
is the maximum period of time Avery Dennison
will warrant the finished products performance in
accordance with ICS Performance Guarantee
Terms and Conditions 1.0, provided that the film
is properly stored, converted and installed in
accordance with Avery Dennison guidelines.
+
Compatible with most printer and ink
combinations. Test prior to use.
Avery Dennison® MPI 1005 Supercast Easy Apply RS Rev. 3 (Jan 2016)
Dimensional stability:
Is measured on a 150 x 150 mm aluminium panel to
which a specimen has been applied; 72 hours after
application the panel is exposed for 48 hours to + 70°C,
after which the shrinkage is measured.
Adhesion:
(FTM-1, FINAT) is measured by peeling a specimen at a
180° angle from a stainless steel or float glass panel, 24
hours after the specimen has been applied under
standardised conditions. Initial adhesion is measured 20
minutes after application of the specimen.
Flammability:
A specimen applied to aluminium is subjected to the
flame of a gas burner for 15 seconds. The film should
stop burning within 15 seconds after removal from the
flame.
Temperature range:
A specimen applied to stainless steel is exposed at high
and low temperatures and brought back to room
temperature. 1 hour after exposure the specimen is
examined for any deterioration. Note: Prolonged
exposure to high and low temperatures in the presence of
chemicals such as solvents, acids, dyes, etc. may
eventually cause deterioration.
Chemical Resistance:
All chemical tests are conducted with test panels to which
a specimen has been applied. 72 hours after application
the panels are immersed in the test fluid for the given test
period. 1 hour after removing the panel from the fluid, the
specimen is examined for any deterioration.
Corrosion Resistance:
A specimen applied to aluminium is exposed to saline
mist (5% salt) at 35ºC. After exposure, the film is removed
and the panel is examined for traces of corrosion.
Test
Methods
MPI1005SC EASY APPLY RS 2.1 mil White Gloss Cast Vinyl with Easy
Apply and RS technology.
41002SC 41070SC 5328SC
5349SC 5332SC 5334SC 41064SC 5337SC 5336SC 41065SC 402917148S
Reviews
There are no reviews yet.