3M TSA-2 Mortar Joint Roller

Description

3M TSA-2 Mortar Joint Roller

3M TSA-2 Mortar Joint Roller
• Designed to install IJ8624 graphic film for textured surfaces.
• Use for conforming large areas of vinyl over a textured surface in detail areas.
• Use with a high temperature heat gun, at least 1000° F, when applying IJ8624.

http://multimedia.3m.com/mws/mediawebserver?mwsId=SSSSSufSevTsZxtUN8txox_GevUqevTSevTSevTSeSSSSSS–

Film Applicators for Textured Surfaces
3M Textured Surface Applicator TSA-1, Large Area Roller
3M Textured Surface Applicator TSA-2, Mortar Joint Roller
3M Textured Surface Applicator TSA-3, Edge Roller
3M Two-Handled Textured Surface Applicator TSA-4, Large Area Roller
3M Power Grip Magic Pad Applicator CMP-1
Note: Some tools and processes in this Bulletin are described and claimed in 3M Patents and pending Patent applications.
Intended Use These tools, except the pad applicator CMP-1, are intended primarily for applying 3M™
Scotchcal™ Graphic Film for Textured Surfaces IJ8624 or 8624 ES to moderately textured
wall surfaces using high heat. The use of such high heat with other films is not
recommended.
Health and Safety
! WARNING Physical Comfort
Any activity performed for a long period of time in an awkward position or with a high
amount of force is potentially a risk for causing musculoskeletal strain, pain or injury. When
applying graphics, follow these practices to improve comfort and avoid injury:
• Alternative your tasks during the application.
• Schedule regular breaks.
• Perform stretches or do exercises to improve circulation.
• Avoid awkward reaching.
! WARNING Risks of Using Heat Sources
• Read, understand and follow the safety instructions contained in both this 3M Instruc­
tion Bulletin as well as the heat-gun manufacturer’s manual.
• Wear a heat-resistant glove on the hand(s) holding the applicator.
• Do not use heat sources near solvent mixtures or residues, or in areas where solvent
vapors may be present at hazardous levels.
• Never use an open-flame heat source in this process.
! CAUTION Ventilation
Always provide adequate ventilation to remove emissions that may result from the use of
heat. Failure to provide adequate ventilation can result in operator exposure.
High Heat May Degrade Foam Rollers and Damage Substrate
High heat directed at the foam may degrade the foam. Always direct the heat toward the
film, not the foam roller.
High heat may also damage the substrate: use with caution.
Air Quality Regulations State Volatile Organic Compound (VOC) regulations may prohibit the use of certain cleaning
solutions. For example, the California South Coast Air Quality Management District prohibits
use of certain solvent-based solutions without a permit and other California AQMD’s prohibit
use of certain solutions without a permit or a regulatory exemption. You should check with
your State environmental authorities to determine whether use of this solution is restricted
or prohibited.

1. Wear a heat-resistant glove on the hand that holds
applicator TSA-2.
2. Set the heat gun to the temperature specified in
Instruction Bulletin 5.37.
3. Direct the heat gun toward the mortar joint. Heat
the film until warm—usually takes only about 2
seconds—and immediately begin rolling the film
into the joint with applicator TSA-2.
4. Using applicator TSA-2, closely following the heat
gun, move continuously at about 2 inches per
second and completely past the outer open edge
of the graphic.
3M Textured Surface
Applicator TSA-3
Use to conform heated film around cut
edges and in corners. This tool is
particularly helpful for mosaic-type
applications.
1. Wear a heat-resistant glove on the hand that holds
applicator TSA-3.
2. Set the heat gun to the temperature specified in
Instruction Bulletin 5.37.
3. Direct the heat gun toward the top edge of the
film. Heat the film until warm—usually takes only
about 2 seconds—and immediately begin rolling
the film into the joint with applicator TSA-3.
4. With applicator TSA-3 closely following the heat
gun, move continuously at about 2 inches per
second and completely past the edge of the
graphic

3M ID  75347064570    UPC#  00051128777923