Avery SF100 SPECIALTY FILMS GLOW IN DARK

Description

Avery SF100 SPECIALTY FILMS GLOW IN DARK
Avery Dennison® Glow-in-the-Dark Film is a
specialty photoluminescent non-coated rigid
polyester film that can be used for exit and
directional signs, identification of fire alarms,
fire extinguishers and evacuation routes.
This product performs in accordance with
ASTM 2030-06: Recommended Uses of
Photoluminescent Safety Markings., meets
ASTM E2072-04 Standard Specification for
Photoluminescent (Phosphorescent) Safety
Markings

BCI Imaging Supplies

Avery Dennison® SF 100-120-S Glow
in the Dark
Permanent Kraft
(formerly: A0820-S Glow in the Dark)
Revision: 2 Dated: 11/26/13
Product Data Sheet
Page 1 of 4
averygraphics.com
AnswerLine: 800-231-4654
Uses:
Avery Dennison® Glow-in-the-Dark Film is a
specialty photoluminescent non-coated rigid
polyester film that can be used for exit and
directional signs, identification of fire alarms,
fire extinguishers and evacuation routes.
This product performs in accordance with
ASTM 2030-06: Recommended Uses of
Photoluminescent Safety Markings., meets
ASTM?E2072-04 Standard Specification for
Photoluminescent (Phosphorescent) Safety
Markings
Features:
• High gloss finish
• Dimensionally stable liner for easy converting
• Excellent dimensional stability
• Non-toxic, non-radioactive
• Uses zero electricity
Conversion:
• Flat Bed Sign-Cut
• Drum Roller Sign-Cut
• Steel Rule Die-Cutting
• Screen Printing
• UV inkjet
NOTE: When screen printing, contact your ink manufacturer for ink recommendations.
Always test UV inkjet compatibility before printing.
Common Applications:
• Safety Signs
• Emergency Exit
Markings
• Evacuation Signs
• Illuminate Pathways
• Location Signs

Face: 8 mil (202 microns)
specialty polyester
Adhesive: Clear Permanent
Liner: 78# bleached Kraft
Durability: Up to 5years
INDOOR USE ONLY
Application
Surfaces:
Flat
Avery Dennison® SF 100-120-S Glow
in the Dark
Permanent Kraft
(formerly: A0820-S Glow in the Dark)
Revision: 2 Dated: 11/26/13
Product Data Sheet
Page 2 of 4
averygraphics.com
AnswerLine: 800-231-4654
Physical Characteristics:
Property Value
Caliper, face 8 mil (202 µm)
Caliper, adhesive 1.0mil (25 µm)
Dimensional
stability
<0.15”(0.4mm)
Tensile at Yield na
Elongation na
Gloss at 60° 120
Adhesion: 24 hr. 5.5 lbs/in (963 N/m)
1 week 6.25 lbs/in (1094 N/m)
Flammability Self Extinguishing
Shelf-Life 1 year
Durability Vertical
Exposure
Unprinted – 5 years Indoor
Only
Min. Application
Temperature
50° F (10° C)
Service
Temperature
-50° – 180°F (-45° – 82° C)
(Reasonable range of
temperatures which would
be expected under normal
environmental conditions).
Chemical
resistance
Resistant to most mild
acids, alkalis, and salt
solutions.
Important:
Information on physical and chemical characteristics
are based on tests believed to be reliable. The values
are intended only as a source of information. This
information is given without guaranty and do not
constitute a warranty. The purchaser should
independently determine, prior to use, the suitability of
any material for their specific purpose. (Data
represents average values where applicable, and is
not intended for specification purposes)
Warranty:
All statements, technical information and
recommendations about Avery Dennison
products are based upon tests believed to be
reliable but do not constitute a guarantee or
warranty. All Avery Dennison products are sold
with the understanding that Purchaser has
independently determined the suitability of such
products for its purposes. Avery Dennison
products are warranted to be free from defects in
material and workmanship for either one year (or
the period stated on the specific product
information literature in effect at time of delivery, if
longer) from date of shipment if said product is
properly stored and applied. It is expressly agreed
and understood that Avery Dennison’s sole
obligation and Purchaser’s exclusive remedy
under this warranty, under any other warranty,
express or implied, or otherwise, shall be limited
to repair or replacement of defective product
without charge at Avery Dennison’s plant or at the
location of product (at Avery Dennison’s election),
or in the event replacement or repairs is not
commercially practical, to Avery Dennison’s
issuing Purchaser a credit reasonable in light of
the defect in the product.
Avery Dennison’s liability for defective products
shall not exceed the purchase price paid
therefore by Purchaser and in no event shall
Avery Dennison be responsible for any incidental
or consequential damages whether foreseeable
or not, caused by defects in such product,
whether such damage occurs or is discovered
before or after replacement or credit, and whether
or not such damage is caused by Avery
Dennison’s negligence.
NO EXPRESS WARRANTIES AND NO IMPLIED
WARRANTIES, WHETHER OF
MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR USE, OR OTHERWISE (EXCEPT
AS TO TITLE), OTHER THAN THOSE
EXPRESSLY SET FORTH ABOVE WHICH ARE
MADE EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, SHALL APPLY TO PRODUCTS
SOLD BY AVERY DENNISON. AVERY
DENNISON SPECIFICALLY DISCLAIMS AND
EXCLUDES ALL OTHER SUCH WARRANTIES.
NO WAIVER, ALTERATION, ADDITION OR
MODIFICATION OF THE FOREGOING
CONDITIONS SHALL BE VALID UNLESS MADE
IN WRITING AND MANUALLY SIGNED BY AN
OFFICER OF AVERY DENNISON.

Avery Dennison® SF 100-120-S Glow
in the Dark
Permanent Kraft
(formerly: A0820-S Glow in the Dark)
Revision: 2 Dated: 11/26/13
Product Data Sheet
Page 3 of 4
averygraphics.com
AnswerLine: 800-231-4654
Dimensional stability:
Is measured on a 6” x 6” (150 x 150 mm) aluminum panel to which a specimen has been applied; 72 hours after
application the panel is scored in a cross pattern, exposed for 48 hours to 150°F (65°C), after which the shrinkage is
measured.
Adhesion:
(FTM-1, FINAT) is measured by peeling a specimen at a 180° angle from a stainless steel panel, 24 hours after the
specimen has been applied under standardized conditions. Initial adhesion is measured 15 minutes after application of
the specimen.
Flammability:
A specimen applied to aluminum is subjected to the flame of a gas burner for 15 seconds. The film should stop burning
within 15 seconds after removal from the flame.
Temperature range:
A specimen applied to stainless steel is exposed at high and low temperatures and brought back to room temperature. 1
hour after exposure the specimen is examined for any deterioration. Note: Prolonged exposure to high and low
temperatures in the presence of chemicals such as solvents, acids, dyes, etc. may eventually cause deterioration.
Chemical Resistance:
All chemical tests are conducted with test panels to which a specimen has been applied.
REAGENT 7 DAY DIP RUB
IMMERSION TEST TEST
30% Sulfuric Acid NE NE NE
10% Sulfuric Acid NE NE NE
30% HCL NE NE NE
10%HCL NE NE NE
50% NaOH F NE NE
10% NaOH F NE NE
MEK F F F
Acetone F F F
Methanol F F F
Is opropyl Alcohol F F F
ASTM #3 Oil NE NE NE
SAE 20 Oil NE NE NE
Toluene F NE F
Mineral Spirits NE NE NE
Glacial Acetic Acid F F F
5% Acetic Acid NE NE NE
Diesel Fuel NE NE NE
Heptane NE NE NE
10% NaCL NE NE NE
Turpentine NE NE NE
Kerosene F NE NE
DI Water NE NE NE
Gasoline F NE F
Avery Dennison® SF 100-120-S Glow
in the Dark
Permanent Kraft
(formerly: A0820-S Glow in the Dark)
Revision: 2 Dated: 11/26/13
Product Data Sheet
Page 4 of 4
averygraphics.com
AnswerLine: 800-231-4654
NE = No Effect
F = Failed (affected sample)
7 Day Immersion: Immersed in reagent for 7 days. Dip Test: Five 10 minute dips in reagent with 30 minute
recovery. Rub Test: Rubbed sample for 1 minute with swab soaked in reagent
Illuminescent
Characteristics:
Charge time of 5 minutes @ 1000 Lux will charge the sign for +10 hours of glow time.
Consistent glow life and unlimited rechargability throughout service life.
Illumination: 21.6 Lux (2 foot candles) for 2 hours with a 4100K cool white flourescent
lamp
Luminence time (after illumination):
10 minutes > 25 mcd/square meter
60 minutes > 5 mcd/square meter
90 minutes > 3 mcd/square meter
Abrasion Resistance: CS-17 wheels, 1000g weights
Withstands up to 9000 cycles
Tested U.S Federal test Method Std. No. 191A, Method 5306
Relevant Standards: Meets or exceeds the following standards. ASTM E-2072-00 / ASTM E-2073-00, ASTM
E-162, ASTM E-648, ASTM E-662, IMO Resolution A.752(18), ISO/CD 15370, Marine
Safety Committee MSC.27(61), DIN 67 510 (Parts 1 – 4), and PSPA Standard 002 Part
2.
Meets OSHA 1910.37, Lloyd’s Register SAS F050294.p
Revisions are italicized
Trademarks:
ANSI: American National Standards Institute (U.S.A.) IMO: International Maritime Association
ASTM: American Society for Testing and Materials (U.S.A.) OSHA: Occupational Safety & Health Administration
PSPA: Photoluminescent Safety Products Association Fed. Spec.: United States Federal Specification (U.S.A.)
DIN: Deutsches InstitÜt fÜr Normung PSTC: Pressure Sensitive Tape Council (U.S.A.)
Avery Dennison is a registered trademark of Avery Dennison Corp.
SF100-120-S PERM KR-A GLOW IN DARK 0820S

A000041 SF100-120-S PERM KR-A GLOW IN DARK 15″ x 10 yd Pun
A000045 SF100-120-S PERM KR-K GLOW IN DARK 24″ x 10 yd
A000048 SF100-120-S PERM KR-R GLOW IN DARK 48″ x 10 yd
A000044 SF100-120-S PERM KR-F GLOW IN DARK 15″ x 50 yd
A000042 SF100-120-S PERM KR-C GLOW IN DARK 15″ x 50 yd Pun
A000046 SF100-120-S PERM KR-M GLOW IN DARK 24″ x 50 yd
A000047 SF100-120-S PERM KR-Q GLOW IN DARK 30″ x 50 yd
A000043 SF100-120-S PERM KR-G GLOW IN DARK 30″ x 10 yd Pun
A000049 SF100-120-S PERM KR-U GLOW IN DARK 48″ x 50 yd

0820SA A000041 SF100-120-S PERM KR-A GLOW IN DARK 15″ x 10 yd Pun
0820SK A000045 SF100-120-S PERM KR-K GLOW IN DARK 24″ x 10 yd
0820SR A000048 SF100-120-S PERM KR-R GLOW IN DARK 48″ x 10 yd
0820SF A000044 SF100-120-S PERM KR-F GLOW IN DARK 15″ x 50 yd
0820SC A000042 SF100-120-S PERM KR-C GLOW IN DARK 15″ x 50 yd Pun
0820SM A000046 SF100-120-S PERM KR-M GLOW IN DARK 24″ x 50 yd
0820SQ A000047 SF100-120-S PERM KR-Q GLOW IN DARK 30″ x 50 yd
0820SG A000043 SF100-120-S PERM KR-G GLOW IN DARK 30″ x 10 yd Pun
0820SU A000049 SF100-120-S PERM KR-U GLOW IN DARK 48″ x 50 yd