ENUINE SILVER EXT. LGE. ENGINE TURN PRINTABLE 15″ X 02 YDS PUNCH

Description

ENUINE SILVER EXT. LGE. ENGINE TURN PRINTABLE 15″ X 02 YDS PUNCH
SignGold .999 Silver is available in 15? wide material. Our .999 Silver products must be applied dry, and are guaranteed, 10 years for interior use only. Proper edge sealing is required and essential for all Silver applications.
SignGold .999 SILVER & NICKEL
THERMAL TRANSFER/SCREEN PRINTABLE
PRELIMINARY
SignGold .999 Silver & Nickel film can be cut with one of many plotters on the market. This authentic silver & nickel
material is NOT warranted for use outside. Having said that, many signmakers are using it outside on fire trucks, boats,
and signs of all kinds. The key to using it outdoors is making sure no moisture gets behind or into the edges of the silver &
nickel. Read the SEALING AND FINISHING section below for important details. Our .999 Silver & Nickel have a 10 year
warranty for indoor applications as long as all technical information is followed.
THERMAL PRINTING
When setting up machine for printing, use the traditional setting used for high performance vinyl. Many printers are
defaulted or set and need no changes. It is advisable to run a test before beginning actual job.
Make sure the material is free of contaminants which could cause poor printing results. Make sure material is dust-free. If
using an Edge ll or FX printer, it is advisable to run at Edge 1 speed to insure good printing results.
If candy effects are desired, use translucent color foils which allow the SignGold patterned film to show through color. If
choosing to go more opaque when using color, use a primer foil first and then print over it with the top color which hides
the patterned vinyl. Results are outstanding. Create your own ideas using various color choices.
*Always make a test print and cut first before proceeding with the job.
CUTTING
Always make a “test cut” before cutting, at least until you have become familiar with .999 silver & nickel
properties.
ALWAYS USE A SHARP BLADE. Cutting an upper case Helvetica “A” or “N” serves as a great test for blade
sharpness.
A standard angle blade used for cutting standard PVC vinyl is fine; no special blade is needed…cuts like butter.
Our silver product cuts and weeds as good or better than a good quality high performance cast vinyl.
Never cut silver & nickel too deep…Just enough pressure to kiss-cut the material so weeding is easy. Cutting too
deep into the poly-liner can cause the adhesive to settle into the cuts thus causing difficulty in getting the silver
& nickel to release from the liner.
Never allow silver & nickel to be rolled backwards (with the release liner to the outside). Try to keep the
material flat as it goes through your cutter to keep down the chance of tunneling. Always cut material at room
temperature and do not cut material during cold temperatures below 50 degrees as premature release from the
liner resulting in tunneling is possible.
WEEDING
Weeding silver or nickel is actually easier than weeding many high performance vinyls. It is recommended that
you weed your job immediately after cutting. Do not leave for the next day.
APPLICATION
Silver & Nickel MUST be applied DRY. Using fluid of any kind jeopardizes the material by introducing moisture
which will tarnish the material over time.
Use a “medium to high” tack application tape. On letters or graphics taller than 8 inches, a “high” tack tape is
recommended. Using a translucent application tape like Transferite clear 1310 or R-Tape clear medium tack
Conform series will make registration to your outline easier.
To insure good adhesion on vehicles, silver & nickel are best applied over high performance cast vinyl like
Gerber/3M 220 series vinyl. On dark color vehicles, high performance cast vinyl is highly suggested under the
silver. If it is necessary to remove the silver or nickel later for some reason, it removes much easier because the
high performance cast material is under the silver or nickel.
NEVER APPLY SILVER OR NICKEL MATERIAL OVER WATER-BASED OR LATEX FINISHES.
When applying silver or nickel to acrylic or polycarbonate sheets, remove substrate protective sheeting and
allow surface to outgas at least 24 hours before applying the silver or nickel product.
Applying silver or nickel over wood or HDU (high-density urethane), the surface must be sealed using an oilbased or epoxy coating to restrict moisture exposure from behind the silver or nickel. We recommend West
Systems Epoxy #105 Resin with the appropriate hardner.
SEALING & FINISHING
Silver & Nickel must be protected extremely well around the edges in particular to keep out ANY moisture. Our
silver & nickel is protected with an excellent clear (PVF Film) on the surface. Used inside or outside, silver &
nickel must be edge sealed completely.
EDGE SEALING WITH ONE SHOT 4005 or 3M Edge Sealer 3950 IS REQUIRED; edge seal using a
traditional brush application to achieve best coverage and protection. Use a liberal coating to insure .999 Silver
or Nickel edges are COMPLETELY sealed to the vehicle background or vinyl if an outline is used.
Quick Clear Tedlar® Laminate, 3M 8519, 3M 8528 and OraCal 290 CLEAR LAMINATES can be used by
overlapping edge 1/4″ to act as an edge seal. Other laminates may be fine but test first. Note that some
laminates are 5 year products and some 8-9 year products–Choose wisely for your expected durability
requirements. Do not use calendered laminates with Quick-Sign Gold Products. Use the best high performance
clear laminate possible.
Linited Warranry: Quick Roll Leaf Mfg., Co. SignGold products are sold with the understanding that the buyer determines product adaptability for the intended use
and test prior to actual use. Quick Roll Leaf Mfg., Co.’s obligation under this warranty is limited to the replacement of SignGold products solely, and will not be liable
for any expense, damage, loss or consequential damages of any kind from use or inability to use SignGold products. THIS WARRANTY IS VOID IF THE PRODUCT HAS
BEEN SUBJECTED TO ABUSE OR IMPROPER CARE.
SGSXLTP02