Gerber 220 Easy Apply Film White 180-10

Description

Gerber 220 Easy Apply Film White 180-10

220 Easy Apply 15” Punched EDGE READY Color Code 10 Yard 50 Yard White 180-10P84750A P84751A

Gerber 220 Easy Apply is a high performance, 2 mil, gloss vinyl optimal for GERBER EDGE-printing, which features pressure-activated adhesive to simplify application of graphics on flat, corrugated and riveted surfaces. Its pigmented adhesive provides maximum color opacity and a non-visible air egress feature. Six- to seven-year exterior life.

DESCRIPTION
Gerber 220 Easy Apply, manufactured by 3M is the latest film technology. The improved air
release channels allow air escape through micro-replicated channels under the film’s surface
without leaving any noticeable channel marks on the film surface itself. The result is a smooth, glossy
graphic film that is faster and easier to apply than conventional films.
This 2-mil repositionable film is EDGE READY™.
Approved by the AAP Equipment Engineering Committee under AAP Specification M-947
INTENDED APPLICATIONS
Gerber 220 Easy Apply is ideal for both small and large graphics over corrugated and riveted
surfaces such as tractor trailers, buses, and other fleet graphic applications. This film can be used
on a wide variety of substrates including ABS resins, aluminum, chrome, glass, fiberglass
reinforced plastics, painted surfaces and flat or simple curved surfaces, with and without rivets.
This film has a grey-pigmented, pressure-sensitive adhesive, which allows for optimum color
opacity.
This film is not recommended for use on stainless steel, non-3M films, or substrates that do not have
a clean, smooth surface or have poor paint-to-substrate adhesion. It is also not intended for
applications where petrochemical contact may occur. If petrochemical exposure is anticipated, refer
to the section below on protecting graphics.
PERFORMANCE LIFE (UNPRINTED)
When applied vertically, Gerber 220 Easy Apply has an expected performance life of up to ten years.
Performance statements are based upon field experience and exposure tests conducted throughout
the United States. Substrate selection, exposure angle, environmental conditions, and
maintenance of
Page 2 of 4
markings will affect actual performance. Continuous exposure in regions that experience maximum
sunny days will result in decreased performance.
SHELF LIFE AND STORAGE
Apply Gerber 220 Easy Apply within one year of receipt. Printed graphics should also be applied within
one year. Film and printed graphics (with or without premask) should be kept in a clean area free from
excessive moisture and direct sunlight. Maintain temperature at less than 100°F (38°C).
Use a paper interleaf between layers of stacked or rolled printed materials. Do not stack printed graphics
face to face.
PRINTING
GerberColor Spot (GCS), Process Pro™ CMYK (GCP), Medal (GCM), and Transparent (GCT) Series
Foils can be used to print onto Gerber 220 Easy Apply. (For information on the performance lives of
GerberColor™ Foils, refer to the appropriate GerberColor Product Bulletin.)
Recommended working environment is as follows:
 Operating temperature: 50ºF to 95ºF / 10ºC to 35ºC
 Recommended temperature for assured printing accuracy: 68ºF to 78ºF / 20ºC to 26ºC
 Operating humidity: 20% to 90% relative humidity, non-condensing (maximum range;
actual range varies by material used)
PROTECTING GRAPHICS
Gerber Technology offers products that are designed to protect vinyl and printed graphics.
Gerber Guard manufactured by 3M is a durable, dimensionally stable, glossy vinyl overlaminate. This
film has a petrochemical-resistant construction and is intended to be used when markings may be
exposed to petrochemical spillage and/or severe handling conditions.
Gerber UVGuard is a custom-formulated, 1-mil, clear, extremely durable polyvinyl fluoride (PVF)
laminating film designed to further expand the resistance to weathering of printed graphics for up to five
years.
Gerber UVGuard™ 9 manufactured by 3M is a 2-mil, glossy, clear, mildew-resistant, polyvinyl fluoride
laminating film with a petrochemical-resistant adhesive system. It is designed to further expand the
resistance to weathering of printed graphics up to nine years. Gerber UVGuard 9 has the highest
protection from UV fade.
Gerber StrikeGuard™ is an 8.0-mil, clear, glossy overlaminate film designed for a variety of applications.
This heavy-duty overlaminate film is ideal for the protection of graphics, up to two years, and is
especially beneficial where printed graphics experience severe handling and forceful impact. Gerber
StrikeGuard is not recommended in applications that require petrochemical protection or where
additional UV or vandal resistance is desired.
Abrasion Guard SPF (Sign Protection Formula) is a clear, top-coat GerberColor Finishing Series
(GCF) Foil designed for use with EDGE® Series thermal transfer printing systems, to protect graphics
from moderate contact and exposure to harmful effects of UV rays. It has an expected performance life
of up to five years (when printed by itself). When applied as a protective overprint on other GerberColor
Foils, Abrasion Guard SPF will extend the life of the base color by up to 30%.
Page 3 of 4
CUTTING
Gerber 220 Easy Apply can be cut on any 15-inch Gerber plotter. A 30° SuperSharp blade is
recommended. Though plotters can be set to full speed for simple geometric shapes and panels over
6 inches high, slowing the speed of the plotter is found to optimize cut performance. User is advised to
test cut before running entire job. This product is not recommended for complex contour cutting.
SUBSTRATE PREPARATION
Before applying your graphic, wash the surface of your substrate with warm water and detergent. Do
not use soaps or other cleaners with lotions or creams as they will leave a residue. Thoroughly rinse
the surface and allow it to completely dry.
Saturate a clean paper towel with a solvent-based cleaner and wipe the substrate surface. Be certain
to follow all manufacturer safety guidelines when using any solvent. Dry the surface with a lint-free
paper towel before the solvent evaporates.
If applying to glass, wipe the surface with a 2 to 1 mixture of water and isopropyl alcohol. Glass
temperatures can vary across the surface. These temperature variations can produce stresses which
may cause the glass to break. Use caution when applying to glass.
Some polycarbonate substrates may weaken when certain vinyl films are applied to them. Because of
this possibility, the user will need to determine if safety items such as helmets, safety shields, and some
windshields are compatible with their vinyl’s adhesive.
Many paint systems (e.g. two-part urethane) and some polycarbonate substrates will outgas if they are
not fully cured. Outgassing can cause permanent bubbling in most films; substrates should be tested
for outgassing prior to final application.
Gerber 220 Easy Apply can be removed with heat or chemicals within 7 years. Be certain to follow all
manufacturer safety guidelines when using heating devices or chemical solvents.
APPLICATION TECHNIQUES
Dry application should be used with Gerber 220 Easy Apply. Panels can be overlapped. Graphics
should be allowed to cure for 15 minutes prior to application.
IMPORTANT – PLEASE READ
Gerber standard tack application tape is required for all graphics produced with Gerber Digital
Color Printing Systems. Due to the unique adhesive construction of Gerber 220 Easy Apply,
application tape can sometimes curl if exposed to the liner for prolonged periods of time.
Therefore, to minimize contact between application tape and the liner, we suggest any of the
following options for graphic application:
OPTION #1: Apply application tape immediately prior to installing graphic
OPTION #2: Trim excess application tape from graphic to reduce exposure to liner.
OPTION #3: If transporting graphic, secure the applied application tape to the back of
the material liner with masking tape.
MAINTENANCE
To clean printed graphics, use a mild, non-abrasive soap with a soft cloth or sponge. Avoid using
alcohol-based cleansers or soaps containing grit or abrasives. Automated vehicle washing systems that
use rotary cleaning brushes should also be avoided.
Page 4 of 4
PHYSICAL PROPERTIES
Thickness 2 mil
Adhesive Pressure activated, repositionable with air release
channels
Adhesive Color Grey
Liner Polyethylene-coated paper
Tensile Strength 5 lb/in minimum at 73ºF (0.9 kg/cm minimum at 23ºC)
Dimensional Stability .0015 in (0.4 mm)
Application Temperatures:
Flat Surfaces (with and without rivets)
Corrugated Surfaces
50ºF to 100ºF (10ºC to 38ºC)
50ºF to 100ºF (10ºC to 38ºC)
Removal Temperature 50ºF (10ºC) minimum (air and substrate)
Operating Temperature -65ºF to 225º F (-54ºC to 107ºC)
CHEMICAL RESISTANCE
Gerber 220 Easy Apply is resistant to mild acids, mild alkalis and salts. Film has excellent water
resistance.
RELATED LITERATURE
Refer to Product Bulletins of relevant foils and materials for product-specific handling, production, and
finishing information.
CONTACT INFORMATION
For help with questions concerning Gerber products, please call your distributor or Gerber Customer
Service at 1-800-222-7446 or (860) 644-1551. Visit us on the Internet at
www.gerbertechnology.com/signage to learn more about our many other foils, materials and equipment.
When sold by Gerber, use only the corresponding Gerber Product Bulletin to determine product details, including but not limited to appropriate uses, warranty and processing.
EDGE, GERBER EDGE, GERBER EDGE 2, Gerber Scientific Products, GerberCal, GerberGraphics, GRAPHIX ADVANTAGE, GSP, and Images on Vinyl are Registered Trademarks of
Gerber Technology.
Abrasion Guard, ColorSet, EDGE Positive, EDGE READY, Gerber AutoMag, GERBER EDGE FX, Gerber FastFacts, Gerber Guard, Gerber HoloGraphix, Gerber ImageCal, Gerber
ImageCast, Gerber InstaChange, Gerber OMEGA, Gerber PermaGrip, Gerber PlastiGraphix, Gerber QUANTUM, Gerber StrikeGuard, Gerber Tone, Gerber UVGuard, GerberCal,
GerberColor, GerberColor Spectratone, GerberGauge, GerberGlow, GerberMag, GerberMask, GerberVision, GS 15, GS15plus, GSP Plot, GSxplus, GSx, ImagePerfect, IMAGE READY,
LexEdge, Matched Technology System, MTS, OMEGA, Process Pro, SpectraShade, and SpectraTint are Trademarks of Gerber Technology.
3Mis a trademark of 3M Company.
©2018 Gerber Technology. All Right Reserved
Category: EDGE READY™ FastFact #: 5572 Supplied by: Aftermarkets Last Modified: 04/26/21