Gerber CONVEX Laminate 8 Mil

Description

Gerber CONVEX Laminate 8 Mil

CONVEX® Laminate 13” Unpunched 10 Yard 50 Yard

8mil P85023A P85104A

Gerber CONVEX® Laminate provides extra durability to graphics conforming to complex plastic shapes like helmets and lacrosse gear. It is available in either 4mil or 8mil thickness.

PRODUCT CHARACTERISTIC SHEET
PLEASE READ BEFORE USING!
Disclaimer:
All of the descriptive information listed above is our recommendation only. This information does not suggest or constitute a written or verbal warranty or guaranty of any kind by the manufacturer or
distributor of this product. Although this material can be printed on with some solvent based printers, the surface characteristics of the material can change from roll to roll, and failure of optimal
printing results are not a basis for returning the product. Purchasers of this product shall be responsible for independently determining the suitability of the material for the intended application.
GT0121 Gerber Technology
Shelf Life:
Outdoor Life:
Service Temperature Range:
Minimum Application Temp.:
Material:
Tests performed | results:
Adhesive Properties:
General purpose permanent acrylic pressure sensitive adhesive works
on most surfaces. Not recommended for low energy plastics.
8 mil. vinyl with 1.4 mil of adhesive
General Description: Clear soft flexible vinyl with a clear permanent acrylic adhesive. Used for over-laminating when conformability is
necessary. Different combinations of Convex® base materials and Convex® laminate can be used to achieve a variety of decal thicknesses
and selling prices.
Test Method
2 years
2 years stored at 70 F & 50%RH
(-40º F to 176º F)
50º F
On curved surfaces such as helmets, apply by rubbing from the center out. When using Convex® as a Laminate, as it is separated from the
liner, if there is too much drag tension applied to the supply roll, it can stretch and curl up immediately after it is cut on a plotter. Laminate with a
cold pressure sensitive laminator or by hand.
Please perform test cuts to determine the best cutter settings for the finished base materials and laminate construction.
Recommended
Application
Techniques:
Omega
Software Settings:
ASTM D 2979
c. 4 lb. load
Tack (gm/sq cm) 180
ASTM D 3654 Method A a. 1 hrl dwell
b. 1 sq. in. surface
Expected Shear 20
Room Temp (hours)
53
13
45
52
63
Average
OZ/IN Ulitmate Peel from
Acrylic
Stainless Steel
Polypropylene
Painted Polycarbonate
Thickness:
Polycarbonate
Glass
82 ASTM D 903 (Modified for 72 hour dwell time)
USE A 45º blade or 60º BLADE on any combination of material 8 mil or thicker.
CONVEX® 8 mil. Laminate
Company:
Gerber Technology
Date Prepared: Address: 24 Industrial Park Rd. W
Tolland, CT 06084-2806
Phone: 800-222-7446
None
No significant toxic hazard. When burned may produce toxic fumes.
No significant toxic hazard.
Flash Point: N/A
ROUTES OF ENTRY: Method Used: N/A
Inhalation: N/A Skin: N/A Auto-ignition Temperature N/A
Eyes: N/A Ingestion: N/A Flamable limits in Air % by Volume: LEL: N/A, UEL: N/A
Accidental Release Measures: N/A Extinguishing Media: Multi-rated ABC extinguisher or water
None
Respiratory Protection: None required Vapor Pressure (mm Hg) Boiling Point:
Skin Protection: No precautions required Vapor Density (air = 1): Melting Point:
Eye Protection: None required Appearance and odor: Reactivity of water:
Exposure Guidelines: None established Specific Gravity (H 0=1) Solubility in water:
Engineering Controls: None required
Toxicological Information: Stability: N/A
NTP: NONE Conditions to avoid: Fire or Excessive Heat
Ecological Information: No Data Avaialble Incompatibility: None
Transport Information: Hazardous Decomposition Products: None
Hazardous Polymerization: Will not occur.
Regulatory Information:
Disposal Considerations: Waste Disposal:
Dispose of in accordance with Local, State and Federal regulations.
Material Name: CONVEX® 8 mil. Laminate
* RoHS, EU Directives 2002/95/EC and 2003/11/EC and
RoHS2, EU Directive 2011/65/EU
Material Safety Data Sheet (MSDS)
NO
YES
UL Recognized:
ROHS Compliant*:
Composition and information on ingredients:
Individual components of this product do not contribute to any known hazards.
OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200): NONE
Hazards Identification:
REACH Compliant:
None of the components present in this material at concentrations equal to or greater than 0.1% are listed by IARC, NTP, OSHA, or ACGIH as a carcinogen.
POTENTIAL HEALTH EFFECTS:
ACUTE:
CHRONIC:
YES
Emergency and First Aid Procedures:
Handling and Storage: Unusual Fire and Explosion Hazards:
Exposure Controls and Personal Protection:
Special Fire Fighting Procedures: In case of fire, use self-contained breathing
apparatus and full protective equipment – all fires liberate toxic gases.
No special handling required other than storing away from
excessive heat sources.
Physical and Chemical properties:
N/A
N/A
N/A
N/A
N/A
Fire Fighting Measures:
General Description: Clear soft flexible vinyl with a clear permanent acrylic adhesive.
N/A
N/A
Other Information:
Carcinogen Status: IARC: NONE OSHA: NONE
TRANSPORTATION AND HAZARDOUS MATERIALS
DESCRIPTION: Not a hazardous material for DOT shipping.
First Aid Measures:
The information contained herein is based on the data available to the
OEM, and is believed to be correct. However, Gerber Technology
makes no warranty, expressed or implied, regarding the accuracy of
these data or the results to be obtained from the use thereof. Gerber
Technology and it’s distributors assume no responsibility for injury from
the use of the product described herein.
N/A
Stability and Reactivity:
OSHA STANDARD CFR 29, PART 1910.1200: This product is considered to be an
“article” under this standard.
SARA 313 INFORMATION: This product contains no substances at or above the
reporting threshold subject to the reporting requirement of section 313 of Title III of
the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 371,
based on available data.
CALIFORNIA PROPOSITION 65: The following statement is made in order to
comply with the California Safe Drinking Water and Toxic Enforcement Act of 1986.
Warning this product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm. This product contains up to
0.01% Toluene in the adhesive.