Description
Gerber PermaGrip Label Stock – 2 mil white
PermaGrip 15” Punched EDGE READY Color 10 Yard 50 Yard White P83928A P83929A
This 2 mil white polyester label stock has an aggressive adhesive that sticks to low surface energy (LSE) substrates such as powder coat paint. This material is UL recognized at temperatures up to 302 degrees F.
DESCRIPTION
Gerber PermaGrip Label Stock is a dimensionally stable, polyester-based film that resists tearing,
abrasion and heat. It has been formulated for use with the GERBER EDGE®, GERBER EDGE 2®, and
GERBER EDGE FX thermal transfer printing systems, in conjunction with GerberColor Foils. It has
an extremely aggressive adhesive for use on low surface energy substrates. It is edge-stripped to
eliminate build up of adhesive residue on sprocketed equipment. U.L. recognized Gerber PermaGrip
Label Stock is available in 2-mil White and is formulated for both interior and exterior applications.
INTENDED APPLICATIONS
Gerber PermaGrip Label Stock is ideally suited for a wide variety of commercial and industrial label
applications in which durability, heat resistance and dimensional stability are required.
This film is not intended for backlit or vehicle applications. It should be applied to flat surfaces that are
clean and dry.
APPLICATION TECHNIQUES
Dry application methods should be used with Gerber PermaGrip Label Stock and panels should be
butted.
Gerber standard tack application tape is required for all EDGE-printed graphics.
Page 2 of 5
SUBSTRATE PREPARATION
Before applying your graphic, wash the surface of your substrate with warm water and detergent. Do not
use soaps or other cleaners with lotions or creams as they will leave a residue. Thoroughly rinse the
surface and allow it to completely dry.
Saturate a clean paper towel with a solvent-based cleaner and wipe the substrate surface. Be certain to
follow all manufacturer safety guidelines when using any solvent. Dry the surface with a lint-free paper
towel before the solvent evaporates. If applying to glass, solvent wipe the surface with a 2 to 1 mixture
of water and isopropyl alcohol. Glass temperatures can vary across the surface. These temperature
variations can produce stresses which may cause the glass to break. Use caution when applying to
glass.
Many paint systems (e.g. two-part urethane) and some polycarbonate substrates will outgas if they are
not fully cured. Outgassing can cause permanent bubbling in most films; substrates should be tested for
outgassing prior to final application.
PERFORMANCE LIFE (UNPRINTED)
Gerber PermaGrip Label Stock has an expected exterior durability of up to two years when applied
vertically.
Performance statements are based upon field experience and exposure tests conducted throughout the
United States. Substrate selection, exposure angle, environmental conditions, and maintenance of
markings will affect actual performance. Continuous exposure in regions that experience maximum
sunny days will result in decreased performance. Extreme temperature cycling over a short time may
result in film cracking. This product is not recommended for horizontal applications.
PRINTING
Use 2-mil White Label Stock settings in your software selection palette. If not available, use Gerber HP
Series 220 normal print settings.
GerberColor Spot (GCS), GerberColor Process Pro CMYK (GCP), GerberColor Medal (GCM), and
GerberColor Transparent (GCT) Series Foils can be used to print onto Gerber PermaGrip Label Stock. If
your application requires a U.L. recognized component construction, be certain to use only the
GerberColor Series that have the following U.L. recognition sticker:
Recommended working environment is as follows:
Operating temperature: 50ºF to 95ºF / 10ºC to 35ºC
Recommended temperature for assured printing accuracy: 68ºF to 78ºF / 20ºC to 26ºC
Operating humidity: 20% to 90% relative humidity, non-condensing (maximum range;
actual range varies by material used)
CUTTING
Gerber PermaGrip Label Stock can be cut on any 15-inch EDGE-compatible sprocketed plotter. A 30°
SuperSharp blade is recommended. Plotters can be set to full speed.
Page 3 of 5
PROTECTING GRAPHICS
Gerber Technology offers products that are designed to protect vinyl and printed graphics.
Gerber Guard manufactured by 3M is a durable, dimensionally stable, glossy vinyl overlaminate. This
film has a petrochemical-resistant construction and is intended to be used when markings may be
exposed to petrochemical spillage and/or severe handling conditions.
Gerber UVGuard is a custom-formulated, 1-mil, clear, extremely durable polyvinyl fluoride (PVF)
laminating film designed to further expand the resistance to weathering of printed graphics for up to five
years.
Gerber UVGuard™ 9 manufactured by 3M is a 2-mil, glossy, clear, mildew-resistant, polyvinyl fluoride
laminating film with a petrochemical-resistant adhesive system. It is designed to further expand the
resistance to weathering of printed graphics up to nine years. Gerber UVGuard 9 has the highest
protection from UV fade.
Gerber StrikeGuard™ is an 8.0-mil, clear, glossy overlaminate film designed for a variety of applications.
This heavy-duty overlaminate film is ideal for the protection of graphics, up to two years, and is especially
beneficial where printed graphics experience severe handling and forceful impact. Gerber StrikeGuard is
not recommended in applications that require petrochemical protection or where additional UV or vandal
resistance is desired.
Abrasion Guard SPF (Sign Protection Formula) is a clear, top-coat GerberColor Finishing Series (GCF)
Foil designed for use with EDGE® Series thermal transfer printing systems, to protect graphics from
moderate contact and exposure to harmful effects of UV rays. It has an expected performance life of up
to five years (when printed by itself). When applied as a protective overprint on other GerberColor Foils,
Abrasion Guard SPF will extend the life of the base color by up to 30%.
SHELF LIFE AND STORAGE
Apply film within one year of receipt. Printed graphics should also be applied within one year. Film and
printed graphics (with or without premask) should be kept in a clean area free from excessive moisture
and direct sunlight. Maintain temperature at 70°F (21°C) and humidity at 50%.
Use a paper interleaf between layers of stacked or rolled printed materials. Do not stack printed graphics
face to face.
MAINTENANCE
To clean printed graphics, use a mild, non-abrasive soap with a soft cloth or sponge. Avoid using
alcohol-based cleansers or soaps containing grit or abrasives.
U.L. RECOGNITION
Gerber PermaGrip Label Stock has been recognized for use by Underwriters Laboratories, Inc. on
several different types of substrates through differing temperature extremes.
The U.L. file number is MH25192. It is UL969 certified, UL file number PGJI2.MH25192.
Page 4 of 5
GERBER PERMAGRIP LABEL STOCK UL RECOGNITION DATA TABLE
USS – Standard UL 969, “Marking and Labeling Systems”
Application Surface Temp (ºC) Indoor Outdoor Additional
Max Min Use Use Conditions
Acrylic paint 150 -40 –
Alkyd paint 150 -40 –
Aluminum 150 -40 –
Epoxy paint 150 -40 –
Epoxy/Polyurethane powder paint 150 -40 –
Galvanized steel 150 -40 –
Glass 150 -40 –
Polyester paint 150 -40 –
Polyester powder paint 150 -40 –
Polyurethane powder paint 150 -40 –
Porcelain 150 -40 –
Stainless Steel 150 -40 –
Epoxy powder paint 125 -40 –
Melamine 100 -40 –
Nylon – polyamide 100 -40 –
Phenolic – Phenol Formaldehyde 100 -40 –
Unsaturated polyester – thermoset 100 -40 –
Acrylonitrile butadiene styrene 80 -40 –
Polybutylene terephthalate 80 -40 –
Polycarbonate 80 -40 –
Polyethylene 80 -40 –
Polyphenylene oxide/ether 80 -40 –
Polyproylene 80 – – –
Polystyrene 80 -40 –
Polyvinyl chloride 80 -40 –
PHYSICAL PROPERTIES
Thickness 2 mil (See Description)
Film Color White
Adhesive Pressure sensitive
Adhesive Color Clear
Liner 90-lb layflat
Tensile Strength N/A
Elongation 0
Dimensional Stability No measurable shrinkage
Application Temp 32°F to 100°F (0°C to 38°C)
Service Temp -40°F to 302°F (-40°C to 150°C)
Removal Temp N/A
Page 5 of 5
CHEMICAL RESISTANCE (UNPRINTED)
Chemical Agent Result
Household cleaners No effect
Mild acids No effect
Motor Oil No effect
Water No effect
ADHESION PROPERTIES (Test Method ASTM D 3330)
Peel From Substrate: Average 15 Minutes Average 3 Days
Room Temperature
Average 3 Days
160 ºF
Oz/in (N/m) Oz/in (N/m) Oz/in (N/m)
ABS 36 (396) 60 (660) 59 (649)
Acrylic 56 (616) 70 (770) 61 (671)
Aluminum 48 (528) 62 (682) 92 (1012)
HDPE 27 (297) 32 (352) 37 (406)
Lexan (Bare) 50 (550) 57 (627) 64 (704)
Metal-Painted (alkyd enamel) 49 (539) 58 (639) 89 (979)
Powder Paint Acrylic 43 (473) 61 (671) 81 (891)
Powder Paint Epoxy 50 (550) 62 (682) 82 (902)
Powder Paint Polyester 32 (352) 33 (363) 65 (715)
Powder Paint Polyurethane 45 (495) 6 (66) 87 (957)
Stainless Steel 42 (462) 61 (671) 107 (1177)
RELATED LITERATURE
Refer to Product Bulletins of relevant foils and materials for product-specific handling, production, and
finishing information.
CONTACT INFORMATION
For help with questions concerning Gerber products, please call your distributor or Gerber Customer
Service at 1-800-222-7446 or (860) 644-1551. Visit us on the Internet at www.gspinc.com to learn more
about our many other foils, materials and equipment.
For help with questions concerning Gerber products, please call your distributor or Gerber Customer
Service at 1-800-222-7446 or (860) 644-1551. Visit us on the Internet at
www.gerbertechnology.com/signage to learn more about our many other foils, materials and equipment.
When sold by Gerber, use only the corresponding Gerber Product Bulletin to determine product details, including but not limited to appropriate uses, warranty and processing.
EDGE, GERBER EDGE, GERBER EDGE 2, Gerber Scientific Products, GerberCal, GerberGraphics, GRAPHIX ADVANTAGE, GSP, and Images on Vinyl are Registered Trademarks of Gerber
Technology.
Abrasion Guard, ColorSet, EDGE Positive, EDGE READY, Gerber AutoMag, GERBER EDGE FX, Gerber FastFacts, Gerber Guard, Gerber HoloGraphix, Gerber ImageCal, Gerber ImageCast,
Gerber InstaChange, Gerber OMEGA, Gerber PermaGrip, Gerber PlastiGraphix, Gerber QUANTUM, Gerber StrikeGuard, Gerber Tone, Gerber UVGuard, GerberCal, GerberColor,
GerberColor Spectratone, GerberGauge, GerberGlow, GerberMag, GerberMask, GerberVision, GS 15, GS15plus, GSP Plot, GSxplus, GSx, ImagePerfect, IMAGE READY, LexEdge, Matched
Technology System, MTS, OMEGA, Process Pro, SpectraShade, and SpectraTint are Trademarks of Gerber Technology.
PANTONE, and other Pantone, Inc., trademarks are the property of Pantone, Inc.
LEXAN is a Registered Trademark of General Electric Company.
3M is a trademark of 3M Company.
enVision is a trademark of 3M Company that is licensed to Gerber.
U.L. and the U.L. Recognized symbol are Registered Trademarks of Underwriters Laboratories, Inc.
GHS (Globally Harmonized System)
©2018 Gerber Technology. All Right Reserved
Category: EDGE READY™ Supplied by: Aftermarkets Last Modified: 02/27/18