Gerber QUANTUM II Intermediate Film Yellow P84851A

Description

Gerber QUANTUM II Intermediate Film Yellow P84851A

Quantum II 15” Punched EDGE READY 30” Punched Color 10 Yard 50 Yard 10 Yard 50 Yard
DESCRIPTION
QUANTUM II is a 3.0-mil calendered vinyl formulated to provide optimum cutting, weeding,
printing, and release results.
QUANTUM II is intended for a wide variety of interior and exterior cut-film applications and has
been designed to work with the GERBER EDGE®
, GERBER EDGE 2
®
, and GERBER EDGE
FX™ thermal transfer printing systems, in conjunction with GerberColor™ Foils.
INTENDED APPLICATIONS
QUANTUM II can be used to produce signs, graphics, displays, and labels of all types. It has a
clear, permanent, pressure-sensitive adhesive which allows it to be used in two-way marking
applications.
QUANTUM II can be applied to a wide variety of substrates including aluminum, fiberglass,
plastics, glass, and most non-porous painted surfaces. The user is responsible for determining
the suitability of all substrates prior to final application.
This film is not recommended for use on corrugated or highly irregular surfaces or for vehicle
applications (Use Gerber High Performance Series 220, 225, or 3M™ Controltac™ Film 180 for
vehicle applications). It is also not intended for applications where petrochemical contact may
occur. If petrochemical exposure is anticipated, refer to the section below on protecting
graphics.
(ii GERBER
Page 1 of 4
TECHNOLOGY
PERFORMANCE LIFE (UNPRINTED)
QUANTUM II has an expected exterior vertical exposure life of up to 5 years.
Performance statements are based upon representative experience obtained from testing
throughout the United States. Actual performance will be affected by substrate selection,
substrate preparation, maintenance of the markings, and exposure conditions. Continuous
exposure in regions that experience maximum sunny days will result in decreased performance.
This product is not recommended for horizontal applications.
SHELF LIFE AND STORAGE
QUANTUM II can be stored by the fabricator for one year. Film and printed graphics (with or
without premask) should be kept in a clean area free from excessive moisture and direct
sunlight. Maintain temperature at 70°F (21.1 °C) and relative humidity at 50% or less.
Use a paper interleaf between layers of stacked or rolled printed materials. Do not stack printed
graphics face to face.
PRINTING
GerberColor Finishing (GCF), GerberColor Spot (GCS), GerberColor Process Pro™ CMYK
(GCP), GerberColor Medal (GCM), and GerberColor Transparent (GCT) Series Foils can be
used to print onto QUANTUM II.
Recommended working environment is as follows:
• Operating temperature: 40°F to 95°F I 4.5°C to 35°C
PROTECTING GRAPHICS
Gerber Technology offers products that are designed to protect vinyl and printed graphics.
Gerber Guard™ manufactured by 3M is a durable, dimensionally stable, glossy vinyl
overlaminate. This film has a petrochemical-resistant construction and is intended to be used
when markings may be exposed to petrochemical spillage and/or severe handling conditions.
Gerber UVGuard™ is a custom-formulated, 1-mil, clear, extremely durable polyvinyl fluoride
(PVF) surface protection laminating film designed to further expand the resistance to weathering
of printed graphics for up to five years.
Gerber UVGuard™ 9 manufactured by 3M is a 2-mil, glossy, clear, mildew-resistant, polyvinyl
fluoride laminating film with a petrochemical-resistant adhesive system. It is designed to further
expand the resistance to weathering of printed graphics up to nine years. Gerber UVGuard 9
has the highest protection from UV fade.
Gerber StrikeGuard™ is an 8.0-mil, clear, glossy overlaminate film designed for a variety of
applications. This heavy-duty overlaminate film is ideal for the protection of graphics, up to two
years, and is especially beneficial where printed graphics experience severe handling and
forceful impact. Gerber StrikeGuard is not recommended in applications that require
petrochemical protection or where additional UV or vandal resistance is desired.
Abrasion Guard™ SPF (Sign Protection Formula) is a clear, top-coat GerberColor Finishing
Series (GCF) Foil designed for use with EDGE® Series thermal transfer printing systems, to
protect graphics from moderate contact and exposure to harmful effects of UV rays. It has an
expected performance life of up to five years (when printed by itself). When applied as a
(ii GERBER
Page 2 of 4
TECHNOLOGY
protective overprint on other GerberColor Foils, Abrasion Guard SPF will extend the life of the
base color by up to 30%.
CUTTING
Gerber QUANTUM II has been designed for cutting on most flatbed and drum cutting (sprocketdriven or friction-fed) equipment. Quantum II can also be hand or die cut. A test cut should be
performed to determine the ideal tool force setting.
SUBSTRATE PREPARATION
Before applying your graphic, wash the surface of your substrate with warm water and
detergent. Do not use soaps or other cleaners with lotions or creams as they will leave a
residue. Thoroughly rinse the surface and allow it to completely dry.
Saturate a clean paper towel with a solvent-based cleaner and wipe the substrate surface. Be
certain to follow all manufacturer safety guidelines when using any solvent. Dry the surface with
a lint-free paper towel before the solvent evaporates.
If applying to glass, solvent wipe the surface with a 2 to 1 mixture of water and isopropyl
alcohol. Glass temperatures can vary across the surface. These temperature variations can
produce stresses which may cause the glass to break. Use caution when applying to glass.
Some polycarbonate substrates may weaken when certain vinyl films are applied to them.
Because of this possibility, the user will need to determine if safety items such as helmets,
safety shields, and some windshields are compatible with their vinyl’s adhesive.
Many paint systems (e.g. two-part urethane) and some polycarbonate substrates will outgas if
they are not fully cured. Outgassing can cause permanent bubbling in most films; substrates
should be tested for outgassing prior to final application
APPLICATION TECHNIQUES
If QUANTUM II is being used as a print medium with EDGE® Series thermal transfer
printing systems, Gerber standard tack application tape is required for use as a transfer carrier.
QUANTUM II panels should be overlapped. Wet or dry application techniques can be used (dry
methods recommended).
MAINTENANCE
To clean printed graphics or cut markings, use a mild, non-abrasive soap with a soft cloth or
sponge. Avoid using alcohol-based cleansers or soaps containing grit or abrasives
PHYSICAL PROPERTIES
Thickness 3.0mil
Film Color Several
Adhesive Permanent acrylic PSA
(ii GERBER
Page 3 of 4
TECHNOLOGY
Adhesive Color Clear
Adhesive Thickness .08 to 1.0 mils
Tensile Strength at Break 3800 psi
Elongation 250%
Dimensional Stability <.020 in (.0008 mm)
Application Temp. 40°F (4°C)
Removal Temp. n/a
Operating Temp. -40°F to 200°F (-40°C to 93.3°C)
CHEMICAL RESISTANCE (UNPRINTED)
Chemical Agent Exposure Time Result
Water 24 hours No effect
Methanol 1 hour Slight edge lift
Etyylene Glycol 24 hours No effect
SAE 20 motor oil 24 hours No effect
5% Detergent 24 hours No effect
Hydrochloric acid 24 hours No effect
10% Ammonium Hydroxide 24 hours No effect
RELATED LITERATURE
Refer to Product Bulletins of relevant foils and materials for product-specific handling,
production, and finishing information.
CONTACT INFORMATION
For help with questions concerning Gerber products, please call your distributor or Gerber
Customer Service at 1-800-222-7446 or (860) 644-1551. Visit us on the Internet at
www.gspinc.com to learn more about our many other foils, materials and equipment.
EDGE, GERBER EDGE, GERBER EDGE 2, Gerber Scientific Products, GerberCal, GerberGraphics, GRAPHIX ADVANTAGE, GSP, and Images on Vinyl are Registered
Trademarks of Gerber Technology.
Abrasion Guard, ColorSet, EDGE Positive, EDGE READY, Gerber AutoMag, GERBER EDGE FX, Gerber FastFacts, Gerber Guard, Gerber HoloGraphix, Gerber lmageCal,
Gerber lmageCast, Gerber lnstaChange, Gerber OMEGA, Gerber PermaGrip, Gerber PlastiGraphix, Gerber QUANTUM, GerberStardust, Gerber StrikeGuard, Gerber Tone,
Gerber UVGuard, GerberCal, GerberColor, GerberColor Spectratone, GerberGauge, GerberGlow, GerberMag, GerberMask, GerberVision, GS 15, GS15plus, GSP Plot,
GSxplus, GSx, lmagePerfect, IMAGE READY, LexEdge, Matched Technology System, MTS, ODYSSEY, OMEGA, Process Pro, SpectraShade, and SpectraTint are
Trademarks of Gerber Technology. 3M and Controltac are trademarks of 3M Company.
©2017 Gerber Technology. All Right Reserved
Category: EDGE READY™ FastFact #: 5567 Supplied by: Aftermarkets
(ii GERBER
TECHNOLOGY
Last Modified: 04/04/17
Page 4 of 4