Description
MacTac Stellar Tuning Film 800
MacTac Stellar Tuning Film 800
4.7 mil Double Layer High High Gloss Cast Vinyl.
• Repositionable clear bubble free solvent-based adhesive.
• For flat or slightly curved surfaces in marine and vehicle wraps.
• 90lb polycoated liner.
• Outdoor durability 2-5 years (2-3 years horizontal).
http://www.mactac.eu/datas/products_docs/t/u/tuningfilm-800-bf-stellar/51fb6778af598-tuningfilm-800-bf-stellar.pdf
PRODUCT DESCRIPTION
TF 800 BF Stellar is 120µm cast vinyl coated with a low
tack micro-structured acrylic adhesive.
CONSTRUCTION
Face material :
120 µm sparkling double layer cast vinyl, cadmium-free.
Adhesive :
Repositionable clear solvent based acrylic adhesive.
Liner :
Highly stable 145 gsm white micro-embossed PE coated
paper.
TYPICAL USES
TF 800 BF Stellar is designed for Vehicle & Boat Hulls
Wrapping (above water line).
It can also be used for various furniture’s & interior
decorations.
DURABILITY
Interior decoration: 10 years
Exterior application:
Vertical exposure Zone 1 Zone 2 Zone 3
All Colours 5 years 4 years 3 years
Horizontal exposure Zone 1 Zone 2 Zone 3
All Colours 3 years 2 years Not Recom
Boat application : above data reduced by 30%
Zone 1: North, West, Central & Eastern Europe, North
America (excl. : USA desert’s – zone 3)
Zone 2: South Europe, Central & South America, Asia
Pacific, Australian South coastal area (from Perth to
Brisbane), New Zealand
Zone 3: Greater Middle East, Africa, Australian Desert
areas & North of Perth-Brisbane coastal area, USA
(Arizona, California, Florida, Nevada, New Mexico,
Texas, Utah), Mexico
SHELF LIFE
2 years stored at 15-25°C and ± 50 % relative humidity.
PHYSICAL PROPERTIES (Typical values)
Thickness (mm) (Film + adhesive) ISO 543
0.150
Face Material Data, 23°C DIN 53455-5
Tensile strength : > 35 N/15mm
Elongation at break : > 150 %
Adhesive Data, 23°C FTM 1
Peel adhesion 180° on stainless steel (N/25mm)
– 20 min. residence: 17
– 24 hour residence: 19
– 1 week residence: 21
Dimensional stability FTM 14
Shrinkage (48 hours at 70°C) : < 0.15 %
(25 cm x 25 cm, sample mounted on aluminium).
Temperature ranges :
Application : +15°C to + 40°C
End-use : – 40°C to + 90°C
Flammability ISO 3795
Sample mounted on aluminium : self-extinguishing.
Solvent and chemical resistance
Resistant to most oils and grease, fuel, aliphatic solvents,
weak acids, salts and alkalis.
PROCESSING
Clean and degrease the substrate
All surfaces to which the material will be applied must be
thoroughly cleaned from dust, grease or any
contamination. Use soapy water to remove the dust and
degrease with isopropylic alcohol.
Application
on flat or slightly curved surfaces
Apply TF 800 BF Stellar with dry application method.
on convex areas
Heat the film with a heat gun before conforming it over
the convex area.
on corrugated or concave areas
If the film is stretched into a corrugation it may pop-out
after a few weeks.
It is, therefore, recommended to cut the film and to
apply it in the corrugation without tension.
on rivets
Apply the film over the rivet with high pressure and
heat it with a heat gun (air temperature over 500°C).
The film may lift slightly after few weeks.
Application on boat
We recommend edge sealing.
Removability
Once heated, TF 800 BF Stellar is very easy to remove,
leaving almost no adhesive residue on car body.
Some adhesive residue may be expected on gel coat after
film removal.
Eventual adhesive residues can be removed with
isopropylic alcohol.
Removability is warranted only on original manufacturer
coating.
Important remark
Compatibility with paints and lacquers should be tested by
the end-user, prior to use.