Magic New Vue Interior Mount Perf 54″ X 40′

Description

Magic New Vue Interior Mount Perf

Magic New Vue Interior Mount Perf
• 7.3 mil interior mount window perf, 60/40 pattern
• White face with a black backside on PE liner.
• Removable/repositionable acrylic adhesive.
• Direct print image on the adhesive for a front view image from the outside.
• Use on clear windows only, does not work well with tinted windows.
• Please see technical bulletins and Features and Benefits for best success.
• Print compatibility: Solvent, Eco Solvent.
• Universal core.

https://www.magicinkjet.com/wp-content/uploads/MAGIC_NEWVUE.pdf

NEW VUE
PERFORATED WINDOW FILM – INSIDE MOUNT
for Solvent and Eco-Solvent Printers

MAGIC® NEW VUE is a one side viewable Perforated PVC Window Film that is specifically designed
to be printed on the adhesive side. The innovative design is both an adhesive and an ink receptive
coating, allowing retailers to mount their graphics inside the storefront eliminating damage to their
advertisements.  No additional adhesives or mounting tapes are required.

PHYSICAL PROPERTIES
Film Caliper: 7.3 mil Perforation Ration 60/40 Adhesive Type: Removable Acrylic
Film Type: PVC Optimum Print RH: 20-80% Recommended Shelf Life: 1 yr
Backing Type: PE Optimum Print Temp.: 70°F (21°C) Indoor life Expectancy* 1-2 yrs
*Based on manufactures testing
APPLICATIONS GUIDELINES

Printer & Ink Compatibility: NEW VUE is compatible with most solvent, eco-solvent and printers, including
VuTek, Roland, Mimaki, Mutoh and HP.

Printer Settings: Print to the white, outer tacky surface. Use SBL-7 backlit profiles or select generic backlit
film or Window Perforated profiles and settings. Set vacuum to High. Set pinch rollers to ½ pressure, using
the outer edge pinch rollers, only. Heater settings: 40c – 45c.

Printer Set-up: The image side is tacky therefore the printer and printer area should be cleaned prior to use
to eliminate debris from settling on the print side. It is recommended to unwind a few wraps of material to
feed into the printer, and keep the media draped on the unwinding roll. Advance the material ½” just before
printing. Do not use take-up reels. Keep the material draped at unwind to avoid tugging. The material can
drape to the floor. It is recommended to place a clean silicone media on the floor under the printer to prevent
debris from collecting on the tacky substrate. Clean printer pull-rollers after printing using printer
manufacturer cleaning instructions.

For printers that do not detect or sense black backing such as Mutoh, Oce and Seiko, affix a sheet of white
paper over the media sensor (36” x 5). WARNING: The printer will not detect the end of the roll and will
continue to print, therefore it is important to stop printing prior to the end of the roll.

Material Handling: Always handle NEW VUE so that the white image side is out. Never bend or wind the
material so that the image side is in. Do not remove the PE liner until time of install. Be careful to handle
the graphic so the imaged graphic does not stick to itself. Graphics can laid flat on a table or loosely hand
wound – image side out, and set on end to dry. If stacking graphics for shipment, use a silicone sheet
between layers. For tube shipments, cover the image with a silicone liner, silicone toward image, and wind
on a 3” core (or larger), image side out. Store unused material in its original packaging.

FINISHING RECOMMENDATIONS
Surface Protection: Use a silicone liner to protect the graphic for shipment. Do not use a laminate or
overspray to protect the graphic.

Application: Apply to a clean, dry surface. Temperature of the application surface should be above 40
degrees. Hold the graphic up to, but not touching the application surface, graphic toward the glass, and tack
down the top edge. While holding the remaining graphic from touching the application surface begin gently
tacking down the graphic, starting from the top, working down and out, using a soft squeegee or roller, or by
hand. Do not stretch. Remove liner after graphic is installe

• Code: 71688