Mojave Carpet Graphics Kit White Vinyl and CLEAR EMBOSSED RIGID VINYL Lam 4.0 mill

Description

Mojave Carpet Graphics Kit White Vinyl and CLEAR EMBOSSED RIGID VINYL Lam 4.0 mill
Catalina Graphic Films’ Mojave Digital Media family of Floor Graphics include Carpet Graphics was developed for promotions,
advertising, graphics and messages intended for short-term, temporary applications on carpeted floors for up to 3 months
under conditions of normal use. It is composed of a vinyl base film used for printing and a slip resistant overlaminating film that
is used to protect the graphics. Both films are coated with a pressure sensitive adhesive for ease of application on a variety of
carpeted surfaces.
RECOMMENDED
APPLICATIONS
• Floor
• Indoor
BASE FILM OVERVIEW
Face Film CFFW 3.5 mil matte white calendered PVC
CFFC 3.5 mil gloss clear calendered PVC
Adhesive R32 clear removable adhesive
Liner 90# Layflat liner
Opacity CFFW CFFC
Good Clear
Gloss Level CFFW CFFC
Matte Gloss
Indoor Durability Up to 6 Months
OVERLAMINATE OVERVIEW
Face Film
5.0 mil.
Clear Embossed
Rigid Vinyl
Adhesive Permanent Acrylic
Liner Clear Film
Opacity Embossed
Gloss Level Matte
Indoor
Durability Up to 6 Months
SPECIFICATIONS
Overlaminating
Film
The overlaminating film can be either a high gloss or an embossed clear film with a permanent adhesive
that is applied to the printed decal with a cold laminating process. The overlaminating film is UL approved
for slip resistance.
Base Film Carpet Graphics uses a white or clear flexible vinyl with a high performance, removable, acrylic adhesive.
This film is available non-top-coated for screen-printing and top-coated for offset or flexographic printing.
Printing and
Laminating
Procedures
The white or clear vinyl base film can be printed by any required method and process (ensure that the
correct film, top-coated or non-top-coated, is used). Avoid silicone-containing inks, as these may prevent
a good bond between the two films. Apply the overlaminating film to the printed base film using typical
cold roll laminating techniques. The rolls of the laminator must be clean and smooth to avoid air and dust
entrapment. After lamination, the product can be cut to the desired shape and size with a die cutter,
guillotine, scissors, etc.
Recommended
Carpet Surfaces
Low Pile (Do not use on Shag or “Carved” Carpets). Compatible with most synthetic fabrics. First apply in
an inconspicuous area when using on natural fibers such as wool or cotton, to ensure compatibility with
adhesive. Apply Carpet Graphics only to carpets that are clean, secure, and in good condition.
Application
Procedure
Remove the release film liner from the back of the graphic and position it on the desired location of the
floor. Lift one edge of the decal. Using a squeegee with overlapping strokes, apply pressure from the
middle toward the edge of the decal.
Important: Squeegee all edges and corners with firm pressure. When more than one panel is used, butt
the edges together. Never overlap the decals.
After application is completed, do not vacuum the decals or the surrounding floor for 24 hours. If the
edges lift at all from the floor, the decal must be removed immediately and replaced, to prevent tripping
accidents.
Maintenance Maintain using normal floor maintenance procedures.
Removal Remove by lifting one edge and pulling at a sharp angle using short, sharp strokes until the decal is up
Carpet Graphics Carpet Graphics are sold in kits of base film and overlaminate. Available in clear and white. Each KIT CONSISTS OF ONE ROLL OF BASE FILM AND ONE ROLL OF OVERLAMINATE ? BASE FILM: 4.0 MIL WHITE OR CLEAR FLEXIBLE VINYL WITH A HIGH PERFORMANCE REMOVABLE ADHESIVE ON A 90# LAY FLAT LINER ? OVERLAMINATE: 5.0 MIL CLEAR EMBOSSED RIGID VINYL OVERLAMINATE WITH A PERMANENT ADHESIVE ON A CLEAR FILM RELEASE LINER

SPMCGFWDP5425N-wht SPMCGFWDP5450N-wht SPMCGFWDP54100-wht