Description

XMR Action Magnets-UFMAM40HE-24

 

ACTION Magnet is the magnetic base component for Signetics® Magnetic Receptive Media. In most applications,
the permanently magnetized material is installed once and serves as the base for the magnetic receptive graphics.
Action Magnet is compatible with all known magnetic receptive media. There are several variations of ACTION
magnet for differing applications.

30-mil Standard energy with indoor adhesive
Hi-tack permanent adhesive ideal for mounting to
smooth surfaces to create backer boards
Supports multiple layers of Signetics®
Standard roll: 24.375” x 50’

30-mil High energy with indoor adhesive
Hi-tack permanent adhesive ideal for mounting to
smooth surfaces to create backer boards
Supports multiple layers of Signetics®
Standard roll: 24.375” x 50’

30-mil Standard energy with PLUS adhesive

A premium adhesive that is resistant to outdoor ele-
ments such as sunlight or larger temperature changes.

Supports multiple layers of Signetics®
Standard roll: 24.375” x 50’

Shelf Life

40-mil High energy double-sided
Magnetized on both sides of the sheet for application

to metal fixtures or magnetic receptive surfaces with-
out the use of adhesives

Supports multiple layers of Signetics®
Standard roll: 24.375” x 50’

Standard Indoor Adhesive
Quick Tack on Stainless Steel CTM- 25 10.0 lbs/sq in
Peel Adhesion on Stainless Steel (30 minutes) PSTC-3 8.0 Lbs/in
Shear on Stainless Steel (1000 g/sq in @ 72°F) PSTC-7 300+ hours
Adhesive Thickness with PET carrier Caliper 0.0029 in
Application Temperature Range Above 50°F
Service Temperature Range 0 – 150°F

Plus Adhesive
Quick Tack on Stainless Steel CTM- 25 4.5 lbs/sq in
Peel Adhesion on Stainless Steel (30 minutes) PSTC-3 4.0 Lbs/in
Shear on Stainless Steel (1000 g/sq in @ 72°F) PSTC-7 300+ hours
Adhesive Thickness with PET carrier Caliper 0.0052 in
Application Temperature Range Above 50°F
Service Temperature Range 0 – 250°F

Lay Flat: Magnet rolls have a curl “memory” that will relax over time. Magnet must lay flat prior to installation.
Magnet must be unrolled, placed curled side down and allowed to lay flat for a minimum of 60 minutes (*overnight
is highly recommended). Trying to install the magnet with curl (pulling away from the surface), combined with the
weight of the magnet, will increase the chance of adhesion failure.
Temperature: To accelerate adhesion to the fixed substrate, it is crucial that the adhesive-backed magnet be warmed
to 50° F or higher.
Weight: Magnet is generally heavy. Use caution and proper lifting techniques when moving or working with the
material.

Tiling: Panels should be applied with a slight gap ( 1/32” to 1/16”) between each one. The gap will allow Signetics®
to span over the seam with little or no visible affect. Butt seaming, can introduce a ridge or tenting that might be

visible in the magnetic receptive layer(s). Although material may appear flat initially, subtle movement in the mag-
net or the substrate may occur over time, making the defect visible.

Surface Preparation: The intended application surface must be clean of dirt, dust, grease and other contaimenents.
The risk of adhesive failure is significantly increased if the surface is not properly prepared and cleaned. It is the
responsibility of the purchaser and installer to prepare and test all intended surface(s) for adhesion prior to final
application.
Adhesive backed magnet is not intended for application to painted drywall or other textured surfaces. Magnetic
receptive paint and high energy double-sided magnet is recommended for direct to wall applications.